Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I created a mesh network with a mesh model which allows me to send a string message over it.
I use one board with a provisioning role and 3 others as provisionee....
Hi team,
Let me confirm what's C0 in the nRF51 32MHz XO spec. It specifies as following but C0 definition cannot be found in the PS. I assume C0 is the load cap where C1...
Hey,
I’m using Arduino IDE to program my nRF52832. I want to connect two nRF52832’s using BLE for master-slave communication. Eventually I want the master to control multiple...
Hi,
I am using nRF52840 DK, and I am creating my program starting from the basic UART example. I am not using threads, just plain sequential execution. I have a chain...
Hi,
I found out, that in the light switch example (SDK for Mesh v.1.0.1) after adding second element with Simple OnOff model in the light_switch_server, it is not possible...
Hi! Im using a nRF51-dongle and the SDK v12.1. There are no exampels for Segger Embedded Studio but in Segger Embedded Studio im trying to use the "Import IAR EWARM/KEIL MDK...
Hi everyone!
Im using Segger embedded studio and its works well to import the keil project to SES. I dont get any errors when building or debugging but i cant se it in the...
I read that in large networks that configuring the relay nodes helps achieve low-latency communication. With the nRF Mesh, is it possible to automatically switch off the relay...
Hello,
I wanna use FDS module and started with FDS example given in SDK 11.
I have used the exactly same functions for initialization but it seems like FDS module is not...
The S120 Central after scanning, connecting, and issues a sd_ble_gap_encrypt() to secure the link. If the peripheral's bond (LTK) is corrupted or incorrect, the sniffer shows...
This: http://www2.keil.com/mdk5/editions/lite/
I guess the principal limitation is the 32K code size, but the full list is here: http://www.keil.com/demo/limits.asp
...
I have Stlink v2 programmer and I would like to use it to flash hex file into my nrf52832 I read a lot of threads about using tools like openocd but none was helpful, I think...
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
