Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
We are working on an IoT application using the nrf52840 Preview DK and would like to interface an external Wifi Module for transfering the acquired data to the internet. Could...
I am using SDK 14.0.0 with Softdevice S132 V5.0.0 and the accompanied DFU libraries. In the examples\dfu\bootloader_secure_ble example I think the logging system has a problem...
Hello,
When I try to read data from UART RX port using serial library, I'm not able to read the data beyond the number specified by
SERIAL_FIFO_TX_SIZE and SERIAL_FIFO_TX_SIZE...
Hey, I'm using raspberry pi 3 model b, with the rasbian strech os running in it. I have followed the tutorial provided by nordic using this link for BLE over IPv6. When I...
Hello, In my case, i'm using some PTX and one PRX. It's working well. Now i want to extend coverage, can i use repeater/forwarder? I tried but have problem with PTX: after...
Hi,
we are using a custom board, with codes tested on a NRF52 DK. We reconfigured the pins and when using pin P0.09 (by default NFC) as an input "active_high" and with ...
Hello,
I've done this steps:
I erased the whole chip: nRFgo Studio/ DeviceManager/nRF5x Programming/Erase all
I programmed the Softdevice s132_nrf52_5.0.0_softdevice...
Hello Nordic Team,
i use SDK 12.3 and SoftDevice S130.
In the template project ( \examples\ble_peripheral\ble_app_template ), the BSP module is used to indicate advertising...
Hello,
For my project I need to send raw data (without prefix or timestamps ) along with system logs trough the same UART.
So far one possible solution is to use NRF_LOG_RAW_INFO...
I've been using nRF24LE1 for development. The HAL library provide the AES encryption for ECB mode. Now I need the decryption function. Does anyone has the realization? Any...
Hello everyone,
I use SDK14.2 and s132 softdevice. I can read "NRF_SAADC_INPUT_AIN0" and "NRF_SAADC_INPUT_VDD" pins and system is working properly.
Working Code like...
Dear friends,
I am using the nRF 52832, s132. I want to know the BER (bit error rate) of the BLE link. How can i measure it? Further, to what extent do other radio interferences...
