Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi @ll,
I have a problem bringing the pyaci up and running.
I used it successfully for everything before but since today it is making a mess again:
When I'm trying to...
I am using secure dfu bootloader from the SDK 12.
I changed the start address of my application. In the bootloader, in uint32_t nrf_dfu_init() { } , calling function nrf_bootloader_app_start...
Hello,
I want to make a simple UART Bridge between Central and Peirpheral. I'm usign nRF52832 with nRF5_SDK v15. There are central and peripheral uart examples in the...
Hi,
I have a working application with Buttonless Secure DFU Service wich runs on nRF52832. I'm able to perform DFU without bonds, but I want to use bonding in my application...
Direct connection after disconnect I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection...
Hi there
I met an error down below.
nrf_log_str_formatter.c(86): error: #29: expected an expression
if (RF_LOG_STR_FORMATTER_TIMESTAMP_FORMAT_ENABLED)
nrf_log_str_formatter...
Does the serial function operate with a soft device. Whenever i have an include statement for serial.h in a file with a softdevice I get a No such file or directory compilation...
I've been going off of the Buttonless DFU example to integrate DFU functionality into an existing project on a custom board. While I seem to have added the necessary includes...
I am programming a BL652 module (contains an nRF52832 with populated DC/DC inductors). I am programming it through the nRF52 DK in SEGGER studio.
When I run the blank (no...
Hi All,
A very general question here. I understand that using pre-defined services like the battery service help standardize the way peripherals send data to the central...
I'm using JLinkRTTViewer to look at RTT output from my code. The problem is that when I try to go into POWER_OFF, it generates a reset instead.
Is there a way to go into...
hi,
We want to position with aoa(angle of arrival) method, can it provide the One IQ-sample is a pair of in-phase and quadrature-phase samples, and Phase and amplitude information...
Hi,
I am using a nrf52840 development kit flashed with the ICMP example provided in SDK 15 and I am using a device with Bluez tools version 5.47 to connect to it.
However...
While investigating problems I'm experiencing with bootloader_secure I believe I've identified an error in the HCI TX finite state machine ( components/serialization/common...
