Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello guys I'm using windows (10) using parallels in a virtual machine in mac (high sierra), all in its latest version.
The board is a PCA10040 V1.1.0. with the bootloader...
I program SD132 into nrf52832 and then program bootloader secure into nrf52832. on nRFToolbox is show name " DFUTARG" I'm using nRFToolbox for OTA. When OTA process is successful...
Hellou, I am developing apllication mesh application from example light switch. In application program i receive data from mesh and this data is stored to external serial...
I am looking for the third party nrf 52832 BLE module in which i need following configurations,
Size is less then 9mm*9mm
Chip antenna or PCB antenna
GPIO pins atleast...
Hi!
I would like to completely isolate the nRF52840 on the Preview-DK (2017.32) on hardware level.
Scenario
I would like to power the nRF IC with the external supply...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
Hello all, I'm working with construction like:
To pass some data between APP and BOOTLOADER. At first I tried to place this buffer to the end of RAM, but after restart content...
Hey Hi all, I am new to BLE Technology and it's programming. Well, I need some help on my project that I am working on. I have multiple (=25) peripherals and I want each peripheral...
I've got a custom board using the NRF52810 with SDK v15.0.0.
I am using the TWIM driver (nrfx_twim.c master mode) to drive an LCD driver IC, a capacitive touch sensor IC...
