After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I'm trying to create a service with 2 characteristics. One is a MTU to send large amounts of data from my peripheral via notifications to the host and the other is a RW characteristic...
Hii everybody I am new to nordic nrf52832 board. i have to implement sensor of inversense ic 20648 (Accelerometer and gyroscope ) sensor using i2c with board nrf52832 in sdk14...
Hi,
I am new to Nordic's softdevice based development and I want to build a basic application for advertising to understand more about the softdevice. I went through the...
I know this question has been asked before, but I couldn't find an answer...
I'm looking for an example of how to use the nRF52832's SWO feature with the SEGGER JLink product...
Hi. I am using nrf52832 SoC with s132 device (4.0.2). Device is acting as peripheral, I have set max BLE connection limit to 1. ble_cfg.gap_cfg.role_count_cfg.periph_role_count...
I'm following the migration guide from SDK 14.2 to SDK 15 , and am a little hung up on the new nRFx module.
All the examples in the new SDK use the legacy drivers but the...
I'm using the CR2032 to power up my nrf51822 with LDO setup, it works well in the begining. But when the voltage drops below 2.6V, my phone cannot scan the BLE. Is it little...
What is expected behaviour of s132 device (4.0.2) if peripheral is initialized with periph_role_count=1 and somebody tries to connect when BLE connection is already establsihed...
Hey Guys,
I'm a newbie on BLE development , I'm trying to run the example "examples\ble_peripheral\ble_app_ancs_c" , It works well first time, but it cannot receive the...
I'm using nrf52832 powerd by a 3.6V regulator in a li-ion powered application. And using one of the IOs (P0.05) as the power supply of other circuits.At the same time, using...
Hi
I am having trouble getting the basic BLE_APP_UART up and running. The UART printf() works, but the BLE module (NORDIC_UART) is not visible in all the devices android...
hi,
i am doing a project where i am using central and client model.
i am using nrf52840 as central device and thingy 52 as peripheral device and i am using sdk 14.2.0...
When using make flash on an SDK11 sketch, s132, pca10040, on Ubuntu 18.04, it successfully builds everything until app_uart.c; when it gets to that point, it outputs the following...
Hello,
I would like to test my code on a NRF52832-QFAB chip with 256kB chip to see whether my code fits into the 256kB flash variant.
According to nRF52832 Rev 1 Errata...
hello
i am using segger embedded studio. with nrf52840 and sdk15.
i was working to set the clock using nrf_clock_lf_cfg_t which is defined in nrf_sdm.h .
nrf_sdm.h is...
