I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
we are using the PPK for a while (Software version 1.0.0). For some reason the calibrated values haved changed and very high current values are showing up. I've recalibrated...
Hi Team,
S132 V5.0 for nRF52832 can support up to 20 links.
If the connected links have different ATT MTU setting, what is the behavior of the device/softdevice regarding...
Hi,
I am using nRF52832 SDK 14.2.0 and i added the header file in project path "nrf_dfu_svci.h" but still i getting the error ..\..\..\..\..\..\components\libraries\bootloader...
Hi all,
I am using segger studio , i am trying to run examples of mesh alpha sdk that nordic provides. I can able to dump the code on board successfully. But if i try to...
I am using the nrf_i2s driver, and it works properly ... with CONFIG.CHANNELS set to stereo.
But for my application, I only need to drive data onto SDOUT left channel. ...
Dear sir please help..its urgent.
i am using below configurations. Nordic - nRF52832-QFAA-B Soft device - 132 SDK - nRF5_SDK_14.2
I am following the "ble_app_att_mtu_throughput...
Hi all,
I am using the nRF51822 BLE with custom board, I want to configure Timer1 to generate IRQ for every 1ms and Timer2 to generate IRQ for every 1us. I want to run...
Hi,
I want to change the UART0 baud rate at runtime (the peripheral has switched to a new rate). Is it enough to reset to (say) 9600 baud, like:
NRF_UART0->BAUDRATE =...
Hello,
I am using the nRF52840 DK with Keil to develop. I have a structure defined as follows:
I have verified that uint8 is 1 byte, uint16 is 2 bytes, and uint32 is...
Hi,
I am using nRF52832 Dk and SD132, sdk is 13.1. I have sent my sensor data to server using external wifi module which is interface with nRF52832 DK.
Everything working...
I have a Client and two Server, so i did flash the example code.
But, from the command '3', i get an error that i do not know.
Can you help me ?
What is correct value...
Hi.
I want to add constant descriptor. Can I save the memory using const variable and BLE_GATTS_VLOC_USER. Will it occur some faults in future?
static const uint8_t value...
I am developing a program with BMI160 with this libraries , but I do not know to which it refers the following code at line 5 and 6: sensor.read and sensor.write.
It is...
I’m using the example “light switch” of SDK Mesh.1.0.1. In my case, i use nrf51 dk as client and three nrf51 dongles as servers but It doesn’t work.
I have tried to debug...
Hi everyone! I'm trying to generate a modulated continuous signal in a specific channel using nrf52832. I used a code made from radio_test example that follows. The problem...
