I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
I have a new nrf 9160 DFK. I followed up the instructions from 'Getting Started Assistant' from the 'nRF Connect for Desktop' app. I was able to setup and build the asset...
Hi,
Our company use nrf24L01+ for many years,the maximum output power of 24L01+ always about 0dbm in our application.But recently we meet a problem that the 24l01+ output...
Hello, as mentioned in subject, I have done DFU on nrf51 DK. it is tottaly working fine. As soon as I try to work with Nrf51822 QFAC custom board. It goes in to bootloader...
Hi,
I intend to use the nRF9160 as an LTE module. I will send data to be transmitted to the nRF9160 and receive data from the nRF9160 via SPI. I have read in numerous places...
I just want timer2 to run at 1Mhz so I can grab a microsecond counter as a timestamp. I don't care that it'll overflow after 32 bits. Put together what I thought should be...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
As per the section - "Adding support for programming nRF5340 in SES" in the document https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html , I had...
Can you please guide me how to compile the nRF Connect SDK asset tracker with the AT command library enabled. I need to set the CONFIG_AT_CMD_RESPONSE_MAX_LEN configuration...
I tried to connect my nrF52 DK board to various devices, via USB. None of the devices was able to see the board.
In addition, nrF Connect / Studio wouldn't see the board...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
