I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
hi :
i following the online LWM2M example document of iot-sdk and setup leshan bs server on ubuntu 16.04 of VM.
i run bs server on ubuntu16.04 of VM and run LWM2M example...
Hi all,
sometimes this events occurs on my code. My start point was the glucose app, to implemented a "just work" pairing and bonding.
When this event occurs a disconnect...
Hello,
one of my project requirement is that i can accept data via bluetooth and rf. i want to know can we use bluetooth and rf in same code. the switching between bluetooth...
Hello there,
While investigating some issues with getting nRF Connect working on Ubuntu Gnome 17.04 , I came across a more fundamental problem.
I now have J-Link V6...
Hi, I successfully modified the Nordic Semiconductor SDK 13's SAADC example adding a feature that performs the FFT of the sample taken and using an RTC is possible also to...
Dear all,
I was following the "Getting started with the nRF52840 Preview Development Kit" page. But when i connect the board to the computer, the board do not appear as...
Is it possible to change the output power of the Thingy to +4dBm and how would one do that.
We are using the Thingy for demos and would like to demonstrate the difference...
Hello:
I have been trying to figure out the proper app ram address base by calling sd_ble_enable.
I am using keil's debug mode, and when the program hit the breakpoint...
Hi, I'm trying to view some logging out put using the segger RTT viwer whilst running keil's debug mode.
I can view some, incomplete loggins in run time (meaning not all...
I find NRF_UICR->PSELRESET[0],[1] can't be written to 0xffff when their values is 0x0015, but the values can be written to 0x0015 when pre values is 0xffff.
so, I can't...
I try to get rssi , but it didnt work. I tried to control what is the problem? , I just want that ; if there is any change , My red led will blink and then I will controll...
I am using Blend Micro with Nokia 5510 LCD.
Before applying BLE SDK for Arduino, LCD works fine.
After initializing BLE UART for nRF8100, send text through nRF8100 by UART...
sorry for short question
almost first step here. I came from eddystone format beacon to here
but I've found long time to add a sensor on nrf51822 module..
some articles...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
