I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
hi ,
Now, My program it have a crash when i to service discovery.
That always stop at when ble try to get the "PrimaryService(0x1801)" Characteristics
but i not found the...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Dear Nordic Support Team,
I am trying to write some information in the flash memory without success. In the ble_flash.h file, it is specified that the pages 0-127 are reserved...
hiii....
1.can any one tell where do we call advertising_start() function if we want to advertise after getting disconnect from a central device.
2.in ble_evt_dispatch...
I`m a newbie at Bluetooth Low Energy and Nordic Chips. I bought a DK for the nRF51822. I would like to set I/O pins over android and iOS application.
1.So what application...
Are there any common solutions to the issue of spi_slave.c using an array as its buffer? I would like to setup a circular FIFO, but I am not sure if there is any way to do...
We are using the S110 as a peripheral that emits data via notifications.
Is it safe for the central to also send characteristic writes while notifications are being emitted...
First of all ,i download the SD7.0 to my device, then i download my app to my device,in this case
my device's curent is 100uA.
First of all ,i download the SD7.0 to my device...
Hello,
i need some informatiorn about the layout of the nRFgo Motherboard. More specific i want to build a board which is connected to the ports P0, P1, P2; therefore i...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
Hello,
We've heard that the BLE transmission packet length may be increased beyond the limit of 20 bytes in a future version of the S110 softdevice. Would you let us know...
