This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello, I've been working on porting a bit-banged control of a peripheral to use nRF51 SPI--which is just SPI rather than SPIM (therefore no DMA). Observe the SPICLK waveform...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
Hello,
I will explain my setup:
I have 2 nRF51-DK each one of them connected via I2C and SPI to two different custom boards. One being the central(nrfA) and the other...
Setup: DK #1 is running native S110/SDK10/nRF51, one service 128-bit w/ 16-bit char:
Service UUID: 0x0xb1ad
Service UUID type: 0x0x2
Service handle: 0x0x0c
Service handle...
I found a discrepancy between a tutorial and an application note.
Step 2.A of "BLE Characteristics, a beginner's tutorial" devzone.nordicsemi.com/.../ calls sd_ble_uuid_vs_add...
Hi,
I tried to familiarise with eclipse environment and i have some problems :
The debug and run button. I searched on google but i didnt found anwser.
How can i define...
I find example : nRF51_SDK_7.0.0_2ab6a52\examples\properitary_rf\esb\esb_ptx_prx .
question 1: can i add this example into my project that build on SDK v610 and it run...
Hello,
I have an problem with DFU on nRF 52 I have followed this thread devzone.nordicsemi.com/.../ but failing to upload firmware.
I have attached screen shot. You...
Hi
I have noticed that the moment I start SAADC task ("nrf_saadc_task_trigger(NRF_SAADC_TASK_START);"), my CPU current consumption rises by 2 mA!
(tested with chip version...
Hello..
I am Using The Balun having Digikey Part No.2450BM14E0003T And Antenna Part No is . 2450AT18B100E
Then it it is Necessary to add Pi network for matching antenna...
I am working on a school project using the NRF51822 with SoftDevice 130 on a custom board and I aim to create an HID gamepad. I am working on my power supply circuit and my...
