Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Dear: Addressee
Hello!
I have a question about the program development of Bluetooth chip.
There is no client program for blood pressure measurement in SDK (15.2.0...
To do a serial DFU I have followed the steps provided in the DFUMaster_UART link.
1) Generated the key using the NrfUtil.
2) Added the private.key and generated a DFU...
Hi,
I try to flash application + softdevice + bootloader into the nrf52810 with following commands but it does not work? Can you look into this?
nrfjprog --program...
Hi,
We are developing central scanning mode for our project requirement. We want to scan BLE tags which are transmitting at every 10 seconds. I have been using nRF52833...
Hello, I have a working application that transmits data to a smartphone using NUS, based off of the uart example. I would now like to integrate bonding into my application...
I have an NRF52 DK and a J-Link mini debugger. I'm trying to connect J-Link debugger to the NRF52 via the debug jumper port. I'm using a standard 10 pin SWD JTAG cable. I...
i m working with fds using segger, i'm trying to perform read and write functions and printing on putty. it showing no errors on building while debuging no output is displaying...
When create 128byte length's CHARACTERISTIC and read with NRFCONNECT on Android. NRFCONNECT returns GATT_READ_NOT_PERMIT even though sd_ble_gatts_rw_authorize_reply() completes...
Hello Team Nordic,
I have a strange problem with the UART:
I am using nRF52840 with two UARTs: UART1 for Debug-Terminal and UART0 for communication with a GPS-Module...
I have developed a code for transferring data through uart to ble. It is working properly. but when I add a line printf to my code the data transmission stops and ble will...
Hello, I am trying to use the Legacy TWI Driver in SDK 15. I have setup my my sdk_config.h file to remove all references to NRFX (New TWI Driver). Only enabling the "nrf_drv_twi...
Hi!
I have download nRF5_SDK_14.1.0, and I have IAR Embedded Workbench IDE ARM 8.20.1
I want compile ble_app_eddystone.eww from examples, but have error:
Error[Lt009...
I'm looking into the use of the nRF52840 as a light switch/dimmer for a Philips Hue system, but have been running into issues with getting connected to the Hue network. I...
I know there have been many posts on this forum regarding a similar issue, I have spent a whole day reading them and trying to get this working, to no avail.
Basically my...
After nRF52840DK is flashed with open bootloader project through J-link ( usb port J2 on the short side of the board), nRF connect is showing the following interface when...
