void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi, We used Nordic SDK12.2 Softdevice3.1 to develop our smartwatch. After launching our product, we got a lot of complains on the connection and re-connection on Samsung Android...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
I am evaluating with the example ble_app_hrs_freertos, found that if I connect to 52832 and then disconnect immediately for some times, the disconnect event may be not catched...
Dear All,
we're using C++ for our development and I try to use nrf_malloc as much as possible.
But there are cases like std::vector's .resize() function and I wonder if...
Hi,
I'm using the ICMP example provided in SDK 15 to test the 6lowpan and wanted to check the RTT from the nrf52832 dev kit.
I managed to do so with the IOT Timer, I check...
Hi,
I'm writing a client which does the OTA DFU for the nRF52832 and I'm a bit confused why the packet characteristic has the writeWithoutResponse property ( https://infocenter...
Hi, I have 2 questions regarding Nrf52840's zigbee connectivity.
1. Is it compatible with ALL other chip manufacturers, or at least, what about TI? CC2530? Zigbee has...
Dear all,
I am testing the light_switch demo (SDK for Mesh v2.0.1 and softdevice 6.0.0) below the following configuration:
-- One client: nrf52-PCA10040 DK (light_switch_client_nrf52832_xxAA_s132...
I read in a CMakeList.txt, that EXPERIMENTAL_INSTABURST_ENABLED is posible on the nRF52832 platform only.
Is it possible to get Instaburst running on a nRF52840 chip using...
I would like to separate the BLE communication from the main.c and place it to a separate file. I followed the example of the default ble_app_template as well as nordic's...
Hello,
Configure the nRF52832 (PCA10040) as suggested in the link below:
github.com/.../Android-Image-Transfer-Demo
Launched the Android Image Transfer Demo and we were...
Hi, i am working on a message model based on the simple_on_off model. I am able to send and receive a buffer via unicast or multicast. Now i am trying to develop a reliable...
