Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I just want to know if this is an expected behaviour of the Softdevice. I have a central that scans every 2 seconds for 1.7 seconds (leaving 300ms for connections...
Hello,
I am thinking to use nRF52840 EVK for our project. I am supposed to use Katalon ( a tool for test automation) and Katalon works with Java. Hence, I will need a Java...
I have an existing setup, where firmware is transferred to a nRF52832 over a BLE USB dongle PCA10031 (V1.1.0) and nrfutil. This setup has been automated on our CI system/tools...
Hello,
I was able to compile my example codes successfully. All of sudden I have started seeing Error starting Process JAVA.
Has anyone faced this issue?
Can you please...
Hello Nordic team ,
I am working in BLE project ,while I am scanning device(filter) am getting (error 18) . Need your help team
Sd ble gap connect returns error code...
Hi.
I am trying to start development using Thingy:52. To start, I tried the firmware from the download page ( https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms...
The Limitations subsection of the Zigbee Section here contains the following paragraph:
- OTA DFU: Migration from the nRF5 SDK for Thread and Zigbee version earlier than...
After installing nRFgo Studio v1.17.1 on Windows 7 64 Bit (using the administrator account), I get an error message in the Log section just when I start the program:
"JLinkARM...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
Hi,
I'm evaluating the Raytac MDBT50Q devkit, using nRF52840-DK to program it. I'm testing the system with SDK project nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c...
