Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
HI NORDIC TEAM
Hello!
Does the NORDIC chip support the BLUETOOTH 3D Synchronization Profile?
Are there any relevant documents or procedures that can be referred to?...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi,
I'm developing my app on nRF52840, NCS2.7.0 on VS Code 1.100.0.
My application needs to save settings data (4 x int32_t ) to external the NOR Flash (mx25r64) in `settings_storage...
Hello,
nRF Connect SDK v3.0.1 nRF54L15-DK v0.9.1
Currently, I’m exploring whether it’s possible to create a Bluetooth application that can be controlled from an external...
Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
I have just purchased nRF54L15 DK, run Quick Start and programmed 'Hello World', but the verification failed and nothing happened. I opened the serial terminal, but nothing...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
Hello,
I am running firmware on a custom board toting an nrf5340 with NCS version 2.3.0. There is also a Micron 8Gb NAND flash on board that I have a custom driver for....
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Hello~ I used the ot-nrf528xx codebase for compilation, and according to the content in the readme, I compiled two Hex files for USB and SPI interfaces using the USB_trans...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Hi,
I am power profiling an application on the NRF52 DK. The application uses SPI to communicate with the BMA400 accelerometer:
The program initializes the accelerometer...
Dear support team,
I am getting an error while performing DFU using nRF Connect.
My SDK version is 2.4.2, I need to do DFU using BLE simultaneously, for that i tried...
