Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
i'm looking for the NRF52832 QFN48 6x6 symbol and footprint in Orcad/Allegro format to accelerate my design,
unfortunately, my electronic designer don't use Altium...
I've been experiencing this bug for a while now. What happens is that a app_timer's overflow handler can't put any more messages into the queue because the queue is full,...
I need to connect to the VSS of the nRF52832-CIAA Ground
A mistake by one of the VSS was not connected nowhere.
The VSS was one N.C..
Do you have any problem with...
im sure the reference design is copywritten if i added two components and removed the GPIO breakouts and switches and led is that in any way not ok? i know nothing on RF signals...
Hi. I am trying to add DFU service to sourse code with existing service. When I try to run service without device manager + DFU or run device manager + DFU without my service...
Hello!
I am trying to build a connectable Eddystone beacon with a Blend Micro board which uses nRF8001 . I used the BLEPeripheral library ( github.com/.../arduino-BLEPeripheral...
Should I call app_sched_execute at least once before the first app_timer_start ? I have a strange bug and I realized that calling it before is a fix but I don't see this in...
Maybe this is a newbie question but, I read that using TEMP is a restricted resource for the SD but I could not find any driver or example to use it correctly.
Can someone...
I am trying to determine the suitable set-up to determine when my system's battery source (lipo battery) is too depleted.
I am running my nrf52 at 3 volts and the Lipo Battery...
Hi. I try to fusion 's130_nrf51_1.0.0_softdevice' and 'flash write'. I checked flash write. but when i implement flash write with s130 softdevice, it is not working. If i...
I have the nRF52 dev kit, and I hooked up pin 13 to SDA and pin 18 to SCL on an I2C device. There are no external pullups on the SDA or SCL lines.
However, the TWIM module...
I tested some features of the new nRF Connect application version 1.0 on PC. The application has a lot of interesting features useful to develop and debug embedded software...
Hello Everyone!
I want to make a project that will recognize some tone in the air, up to 5KHZ, and will send nrf8002 a message as a result.
I though to use the nrf52 proccess...
