after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I made a board without external 32kHz crystal.
So, I changed NRF_CLOCK_LFCLKSRC source to NRF_CLOCK_LF_SRC_RC, which is used in ble_stack_init.
Now, I need to make DTM...
Hi,
I am use Exclusion list for my one application.
Exlusion list work is ok,but i am facing problem for how clear Exclusion list ?
My Controller: nRF514222 Rev 3,...
This is my first time working with a microcontroller and working with C as well, my only previous experience being C++ done in notepad on Linux. Currently I'm trying to just...
To reduce nRF52 design thickness, I'm planning to use a low profile inductor on the DCDC converter.
The low profile inductor has a higher resistance, compared to the recommended...
Hi, All.
Once I wrote data in NV memory, it's OK. I can get the same data I put in.
But, after power off - on reset, data are invalid. It's all 0xff(erased state).
I used...
Hi,
I have been trying to do it and even though I have generated packages using the old nrfutil and the new 1.5, when I use nRF connect to do the upload it aborts without...
I programmed my beacon with this code:
ble_app_beacon.zip
I use nrf connect app to see its signals. nrf connect can find my beacons but it says:
serviceUUID : N/A
TxpowerLevel...
Hi all,
I believe it should be possible to defined a characteristic which can be written to but have no automatic write response ACK sent. Instead I want to send a manual...
I develop a temperature sensor sending a temperature and battery status every second.
Used to work fine on previous nRF Toolbox.
Today on my Android 6 and latest nRF Toolbox...
Difficult to obtain the high-ohmage resistors in the solar beacon reference design. Will 5% resistors suffice or do the resistors have to be 1% tolerance.
I have difficulties understanding the COMP APIs, this function below starts after initializing the COMP the peripheral.
nrf_drv_comp_start(NRF_DRV_COMP_EVT_EN_CROSS_MASK...
I am using the nRF51822 utilizing the internal LDO setup. I received a question during regulatory submittal that I am not able to answer and am looking for help on. Is the...
Hi
I've tried to update some of our environment to the SDK12 files. When I tried to compile some of the files a weird bracket error showed up.
At the end i could find...
