Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
For nRF5122 BLEStack, it is analyzed that the event is processed in each of the interrupt handler for the interrupt terminal BLE
I understand that is processed through the...
I tried to set a GATT server and a GATT client for each Central and Peripheral, but code exceeds the memory limit.
Then i consider to transport by HCI. But I totally confused...
We have code that must erase a page in flash every once in a while, while S110 is advertising. The advertising interval is set to 0xF4 (which is about 150ms) and we have scan...
I am using nrf51_sdk_v6_0_0_43681 and s110_nrf51822_7.0.01 wiht nrf51822, and I modifiy code based on ble_app_uart.
Here I am trying to launch a continous ADC sample with...
Hi,
whenever i try to program the PCA10000 ( USB dongle) using MASTER CONTROL PANEL(3.4.0) i'm getting log messages like as below,
"...........
Successful flash!
Enabling...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm following nAN-29 and when I go to import the Eclipse project file for ble_app_hrs I get a message "No projects are found to import". I've pretty much followed nAN-29 to...
I've been working on an interrupt driven I2C driver. I have the basic driver working, but I'm hoping to squeeze a bit more speed out of it.
I'm mostly doing fairly long...
This is an howto on restoring your nRFgo motherboard firmware.
Error code can be similar to this from nRFgo Studio:
Starting bootloader on board 0
Could not start the...
(I also posted this on the mbed BLE_API forum)
Hi all,
Sorry for the long post, I'm starting yet another discussion on BLE throughput, but I feel this merits a deeper...
