I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi,
I wonder if there is any way to disable the Rx FIFO so that I don't have to fill it to generate an event, since I need exact timing for every incoming byte.
Also,...
Hi, I am trying to connect N51422 server to anther vendor's client... the devices always disconnect after 30 seconds of connection.
I found that the reason of the disconnection...
I have seen this question asked on this forum in several ways but none of the parameters match up to my specific case. I am getting this error when I try to run the example...
Hi,
I load the s110 softdevice (I tried many versions 5, 6 and 7)
When I load my app on the SOC using Keil and the nrf_xxaa_s110 (256) target, the app doesn't run.
I'm...
Dear Nordic Developer Zone,
I have implemented a real-time-clock using application timer which is based on the on-chip real-time counter on NRF51822.
A concern of mine...
I'm trying to get the Nan-36 example working on my PC10001 board and I'm having some trouble. I've tried using both SD110 version 6 and 7 with appropriate (I think) memory...
Hi,
Is there any connection/disconnection API in ant+ (sd210) similar to BLE?
I want to use this to control the device activity cycle, if I get disconnection event, would...
Hi,
I'm trying to implement a specific communication protocol using the SPI on a nRF51822. The SPI on nordic side will act as slave. When CSN line goes low, I will also need...
Hi,
I currently have a problem with the continous scanning mode. I implemented the scanning mode that my device searches for the first 4 seconds after power up then picks...
Which example projects are compatible with s110 v7 for nRF51822?
I keep running into samples requiring "Legacy Keil" to be installed.
I just want a clean s110 v7 example...
Uint32_t data using sd_flash_write written many times to the same address, you must perform sd_flash_page_erase before writing it?
(English is not good, with Google Translate...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
Could you please let me know the current rating in between retries while transmitting.From the oscilloscope reading, that is not obvious. The documentation shows three idle...
Hi
We had some problems updating our devices with the nRF Loader App on IOS. After selecting the device in DFU mode the App hangs and aborts with a Bluetooth error after...
