after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi. I'm trying to use GCC instead of Keil.
I have followed "nRF51 Development with GCC and Eclipse" written by Nordic and "nrf51-pure-gcc-setup"( github.com/.../nrf51-pure...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello.
I use nRF51822-EK.
I test ibeacon example source now, but i can't config my minor id.
Now my board minor id is 252(0xfc), I CAN'T CHANGE MINOR ID!!!!
How to T_T...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
Hello,
I'm trying to use the nRF51822 evaluation board like a HID keyboard, so I'm fallowing a tutorial and I installed :
Keil mdk474
nRFgo Studio 1.17
nRF...
We are preparing BQB test for our BTLE product now.
Could you please help confirm if you have the test command to make 51822 into the test mode and can be auto-testing by...
Hi, I'm developing a HID-device using nrf51822, s110 ver 6.0.0 and SDK ver 5.2.
I would like to hide the device from unknown centrals once it's paired. I'm advertising...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
I'm using ble_uart_app & master control panel v3.5 for debugging uart communication. when uart is sending data to host(master control panel side), suddenly, master control...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Hello,
i use the bond manager together with a own module to store data in memory. On user interaction i want to delete the whole memory. I proceed as follows:
Disconnect...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
I am using the eval board, sdk v5.2.0, s110 v5.0 and a galaxy nexus with the UART Nordic app. I have not been able to receive any data on the android end. After
void nus_data_handler...
