Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi
I used the example from nrf51822_v4.4.1.31827\Board\nrf6310\spi_master_example for my PCA10001 board, as I know the pins configured in this example are for nrf6310 board...
Does anyone know how to implement a wrist watch LCD display? I mean a bare LCD Display, without a pre-build driver (I2C). Can I do it directly or I need another IC to drive...
Does anyone have any solid numbers on the maximum throughput achievable on
the nRF51822 USB dongle that comes with the nRF51822 Eval Kit?
Application - OTA protocol Gazell...
Dear Support Team,
currently I'm working on a custom board which contains the NRF51822_QFAB_A0.
I installed the softdevice (not the most recent version, but a version...
Hi,
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Where is it? Please tell me.
...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
it register a handler, what about restart and run pstorage_register again, how it insure everytime we get the same address for our content in the flash?
before pstorage_register...
I'd like to measure the voltage of a lithium ion battery every minute or so in a way that's highly accurate. I need to do this without using the Soft Device because a) I need...
Hello,
We are wondering if the source code for nRFgo Studio is available? We mainly just want to look at the code for examples in creating our production flash programming...
nrf51_sdk_v5_2_0_39364\nrf51822\Board\pca10001\s110\experimental\ble_app_uart
And I just find this device as a bluetooth device but can not find any new uart device under...
Hi
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Could anybody tell where it is...
Hello everybody,
I have a few questions about the built-in UART (UART0) in the nRF51822.
I've noticed some registers that aren't fully documented in nrf51.h of...
