I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
I'm playing with open-source IoT over Bluetooth and recently was told about TI's new SensorTag product line which uses a CC2650 multi-sensor bluetooth base platform with pluggable...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I'm having a weird issue where the stock sdk 8.1.0 DFU software is not timing out properly and getting stuck in the bootloader, advertising dfuTarg forever.
Our iOS app...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
I want to add a battery level characteristics to a custom service. Here is my approach:
In main.c, I add a timer to update battery level periodically
void data_update_timer_timeout_handler...
So I've been having issues with my debuggers where occasionally Keil will crash and I won't be able to reconnect to the debugger interface without a power cycle (might be...
Hi, My project is that when a button is pressed on a slave (nrf51822ek), a central (another nrf51822) gets to know which slave has triggered and sends its status 1/0 to a...
Hello,
I am using ISP130301-Development Kit 1 for nRF51822 from insightsip.com which consists of postimg.org/.../
There is used a button on PCA10028 for deleting bonds...
Hello, every:
I have success to use sd_ecb_block function to encryption data. But I am not find how use this function to do decryption. Please teach me how to use this function...
I am trying to perform a simple ADC measurement using polling rather than using an interrupt. I have looked at examples and read the ADC section in the reference manual, but...
Hi Team,
Is there any way to enable/disable all interrupts?
Will BLE connection get disconnected because of this? If yes the what are the possible ways to
maintain the...
Hi,
I am new to all this,
I have just started using the nRF51822 evaluation kit.
I have manged to run the blinky example, however, eventhough I managed to download the...
After implement PWM (using pwm example at nRF51_SDK_8.0.0\examples\peripheral) into my BLE based nRF51422 project using SoftDevice S110, it has been working fine; however...
I want to add a command ordering by uart to make MCU entering Bootloader mode in app.
To achieve this function, I plan to use the two following example in SDK 8.0
ex1...
I am using nRf51822 series controller here i want to customize advertising request and other parameters, so i want to develop a radio code but without using stack. So can...