I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I'm trying to send data acquired from the ADC and monitor it using the master emulator.
The values I'm getting do not appear to make sense though.
I'm using the BLE_HRS...
Hi,
Original UART DFU bootloader SDK example ported from NRF6310 board to PCA10001 board does not work.
What did I do wrong - can anybody please help me ? Thanks in...
It's possible this is a hardware problem, but what I'm seeing is this...
The clock is enabled on pin 0, data on pin 4. With both enabled in exactly the same way, drive...
Hi, I am trying to get the rssi value of a connection, and what I am trying to do is to start the rssi in the beginning at the connection and end it at the end of connection...
Using S110 version 6.0.0, Sdk 5.2.0, GCC 4.8 (C++, but that don't matters here).
I want to know, if the central has switched Notification and/or Indication on or off for...
Hi,
is it possible to use the PCA10000 as a data logger, to transmit the incoming data over USB to a terminal programm? Are their any limits, e.g. for the data rate?
...
Hey guys,
We're seeing a problem with weird reboots after our system goes through a firmware update using the DFU. We are using the latest GCC for these builds (4.8 2014q1...
Hello,
I was wondering if Nordic plans to offer a dual core variant of the nRF51822? We are starting to see vendors offering dual core BLE radios with one ARM core dedicated...
Hi All.
I am trying to download the Bootloader to nRF51822 Dev Kit using nRFgo Studio (32 bit, v 1.15.1.2691) but getting an Error.
"ERROR: Attempted to write to UICR...
Hi, I am trying to write code to run the nRF8001 chip from a PIC microcontroller. I've been messing around with nRFgo Studio for generating the setup data, and I've noticed...
We need to send some custom data in advertising packet.
Is it possible to use 'ble_advdata_service_data_t' with UUID of a standard service (e.g. battery service or device...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hey all:
I have the Dev and Eval Kits and a handful of dongles. In addition to one of the Chinese nRF51822 devices. I have successfully connected via Segger debugger, used...
Hi.
I have a custom nRF51822 PCB with SWDCLK and SWDIO Header. I have a nRF51822 Dev Kit.
Is there any way to use the J-Link from Dev Kit to Program the Chip of the...
Hi,
I check the state of an channel (sd_ant_channel_status_get()) and get 0x13. Which mean the channel is assigned. But sd_ant_channel_unassign() return with ...CHANNEL_IN_WRONG_STATE...
