Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
I am using nRF9160 to develop a product for a client that requires displaying the name of the current carrier on the screen. According to the AT instruction manual of the...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hello,
I'm new to this development environment and trying to get one of your projects to build for the nRF9151-DK. I recently installed everything with the latest versions...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
