Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
I am studying to use the nRF2460 or wireless digital audio streaming where one Tx broadcasts and several receivers listen and follow. I have the following questions: Can an...
Hi,
How can I read out a vendor model in the NRFMesh app? When I change the model ID to e.g 0x9000, I cannot see the model under elements anymore. Needs there to be any...
I have a list of characters and trying to put them in a string.
char line[13]; /* Line buffer */
NRF_LOG_INFO("Playlist : %c", line[0]); this works displaying 1 character...
We are currently evaluating the two development kits of nrf91 - On the nordic Thingy with Fractus antenna we get the nrf91 into the mobile network after about 20 seconds ...
I know this may be a duplicate of this: https://devzone.nordicsemi.com/f/nordic-q-a/37732/nrf52840-spi-clock-line-contention-causing-spi-driver-to-hang/145521#145521
I say...
Hi,
My working environment:
NCS folder Tag:v1.2.0
J-Link version : v6.62a
SES version:4.42a
test sample code:\NCS\nrf\samples\nrf9160\cloud_client
nrf connect...
I generated two packages for OTA. The first package contains a bootloader and a softdevice 7.3.0. The second one contains a bootloader and a softdevice 8.0.0. I flash the...
Hello,
I want to interface nRF9160dk with ICM20648 sensor using SPI communication protocol. I tested SPI on nRF91 and it is working fine. But how to use ICM20648 with nRF91...
[Embedded World 2020] Failed update of the Thingy 91 Certificate after downloading from the nrf cloud
I Just tried to update the certificate from the NRF Cloud ( https...
https://github.com/NordicPlayground/nrf5-calendar-example
What is lowest power mode where real time clock could run?
How could retain RTC value during reset?
Thanks
I have been using nRF9160 DK for a while, with program running and all, however today I failed to connect to it using SEGGER Embedded Studio with the following error.
...
Light switch, client, server and app nRF Mesh works. I replaced client with ble_app_uart_coexist, but I already donť see it in your nRF Mesh app on my phone. I would like...
