Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Dear all, I have a question about custom address add. In light switch example, we can publish message to group address or unicast address. In my project, we want to send message...
hai ,
i am connecting 5 peripherals in one central (used ble_central example modified like multilink central)
i referred this link for sending particular data...
https...
Hello,
the well known problem of the nRF5SDK is that if you want to use nrfx drivers, you should enable in NRFX_DEFINEs and LEGACY_DEFINEs in config file. For example, we...
Hi ,
In my application .. I have define two custom characteristics one with write permission and other with read + notify permission...
Whenever a value is written to...
Should the toplevel declaration bool nrfx_power_irq_enabled; in nrfx_power.c have a `static` qualifier? I'm using openocd/gdb to load a GCC-compiled firmware onto a custom...
Hi,
I think I have properly configured my application to authorize reads on characteristic, yet I do not see an event generated. I get write events, but I don't get read...
Hi,
I am developing a custom board with nRF52811 where I will measure analog signals from op amp on ADC (single ended mode). Signals will be very small, so I need a good...
Hello guys. I'm beginner in Nordic Devices.
I'm working in project that sends Acceleration Data from KX220 sensor over LoRa network or if there is a BLE device connected...
Hi，
I find that nrf52 series can support Bluetooth 5.2 SoC in nordicsemi page, but it still shows Bluetooth 5.1 SoC in Product Spec.
Which one is right ? Is it just that...
In the User Guide for the nRF52840DK on pg 26 is:
8.5 External memory The nRF52840 DK has a 64 Mb external flash memory. The memory is a multi-I/O memory supporting both...
Hi,
I'm working with the USB_CDC_ACM example to communicate with a PC trough COM port. It works well.
Now I would like to use the ISO endpoint feature in order to transfer...
I have a NRF52840 DK, with a pca63511 power profiler kit purchased just a few days ago from Mouser. I am trying to use the power profiler kit with version 2.3.1 of the power...
We are in a need to upgrade the existing Soft Device to higher version from the application firmware. The reason why I am asking this, if it is possible to upgrade then we...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
I am using NRF52840 in Mesh (SDK 4.1.0), I am facing this strange issue, one of my node (have client+server both) is got damaged, I replaced this with new NRF52840, then I...
