Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
In our application, LCD will occupy 150KB RAM, and algorithm will occupy 60KB, but 52840 only has 256KB ram, so 256KB RAM is not enough for our application;
We want...
To realize multi touch in hid, we need to realize get report request to get the maximum number of support points and set report request to set touch mode. In the SDK 15.3...
Hello,
I'm trying to add a third characteristic to my BLE service and when I add it, my device "fatally" crashes in Release mode with no meaningful error information ...
Hi I'm having trouble updating the firmware on a custom board using JTAG through the NRF9160 DK.
I've attached the log file from the programmer of the error I'm getting...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
Hi
nrf52833 SDK16
The following code works fine on UART 0 but not on UART 1
The problem seems to come from nrfx_uart.c
There is no support for a UART1, so...
Hi,
I've built a project out of the USBD_ACM_CDC example in which I have added a SPI master driver. This project has a timer interrupt that will shoot off every ~500us and...
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
Hi every one,
I'm a development product with chipset NRF52811, using soft device S112 and SDK 15.3.0.
My device will wake up and send data whenever I press the button...
Hello Nordic Team, I'm starting a project which consist in measure pressure in multiple points and send this data to central unit. At this point, using strain gauges with...
Hi,
I am using the Thingy 91 and I have a program, where I first read GPS, then switch to NBIoT Mode and then send the data to a server.
However if I switch the Antenna...
Hi, Nrf Connect was used as a central.When I send a data (Uart Service) from the app to the characteristic value of a Service (UUID:0x0002), the callback function of another...
