Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Due to the covid-19 virus, my school project changed a lot. The new project is the following: "Study the latency between sending and receiving data from a device generating...
Hi, regarding a nRF24LU1, we are developing a system composed by 4-5 sensors (eachone based on nRF24L01) that send acquired values to a single nRF24LU1 receiver connected...
Hello,
I am trying to drive a custom display with the QSPI driver on the NRF52840.
Is there a way to disable the memory addressing on the QSPI driver and just write out...
What's the recommended way to manage cloud credentials on the device? Right now we're storing hard-coded username/password for testing but obviously this is not acceptable...
Hi,
We have a stability issue with nRF52840 DK after it has been upgraded to JLink DLL version V6.60e and firmware OB-SAM3U128-V2-NordicSemi compiled Jan 7 2019 14:07:15...
I have been looking into using Bluetooth Low Energy 5 advertising features like periodic advertising and advertisement chaining, but have not been able to have any luck with...
hello
we want to connect FPGA to 52840 using QSPI interface for data transfer, 52840 used as master, and FPGA as slaver. so we use write opcode PP4O for 4 lines writing...
Hello,
I want to read two files from SD card using nRF9160dk. I tried this code ncs/zephyr/samples/subsys/fs/fat_fs.
The Code:
I am getting the following error:
...
I need FreeRTOS operation in my build. I've adopted the FreeRTOS.h file from the blinky_freertos example, unchanged aside from a larger heap size and setting INCLUDE_xSemaphoreGetMutexHolder...
Hi all,
I have the nRF51822 chip and I want to acquire external sensor (i.e. pressure, temperature) and send the information via bluetooth.
I need to configure the I/O...
Hi
I using nRF52840-DK with 64 Mb external flash memory.
I'm using SPI interface for read / write command with the external flash.
When I'm using single command for...
I am attempting to implement AoA using the nRF5340 Preview development kit and 3 BMD-360 modules with the nrf2811 SoC.
In searching the devzone I see multiple comments...
Hi ,
I am following the instructions here:
https://bifravst.gitbook.io/bifravst/bifravst-on-aws/simulator
to deploy the web application, and the web application says...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
