Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, basically I want my nRF9160 DK to establish a secure connection with DTLS by using mbedtls .
What I'm trying to do
I'm currently working with the LwM2M sample...
Hello,
My NUS services work fine i can transmit and receive data over UART , but i still get this error in my nRF Toolbox (UART) . Any help will apreciated
Some user datas have been stored in a special page of flash in nRF52832 . However , I need to reprogramme the chip through bootloader , and make sure the user datas not being...
Hi,
I am trying to evaluate the nRF52840 development boards and configure as a simple switch and light node.
The first issue I have had is that on a Huawei phone the nRF...
Hello,
I am trying to find out where to put my persistent storage data in flash.
I have to set start_addr and end_addr, to use fstorage, but I dont know what addresses...
Dear Nordics,
i'm getting started with development on Laird BL651.
Issues as follows:
It appears to be neccessary to switch to internal RC oscillator and adjust the...
Hi,
We are facing an issue related to battery life. We are using sdk 15 and SD S132(7.0.1) and we are able to archived 30uA current consumption, but we want it near to 5uA...
Hello,
I am using SDK v11, SoftDevice v132 and Keil Uvision 5 to program on my nrf52832 SOC on the development kit(PCA10040) for our project. I need to save a few uint32_t...
I am trying to evaluate the nRF52840 and can't find the source code for any of the project - only the hex files to run applications.
Where can I find the source code?
...
Hi,
We have developed a mouse with nRF52832 using the ble_app_hids_mouse example.Now, I would like to add consumer usage into the hid descriptor to control media. So, I...
Hi,
I am currently working on nordic PDK. And I am interested in flashing nRF52840 through FTDI SWD interface. I want to know whether it is possible?
If yes, what will...
Hi,
We are trying to develop custom uart bootloader firmware without using MBR. also we are not using softdevice.
Here are some linker definitions which are implementation...
Hi! I'm working with a custom board, where pin p0.18 is connected to an external button.
I've read several posts, including this one which say that one must remove the ...
Hi, I'm unable to get a working example with the bootloader, softdevice and application. I'm following this: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts...
Hello There,
i have made an Selfmade PCBA with an nRF52810 and it is my first time that i am working with those Chips.
I have used the reference Design for this board...
