Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
I need to share the LFCLK with an external device and I'm thinking on using an external oscillator like SiT1532AC-J5-DCC-32.768E
I'll set the LFCLKSRC registry as 111 (Apply...
I am setting up a build server that will take care of building our app for the nRF52 and creating the DFU files. For DFU package, I need nrfutil.
Everything is working fine...
The document infocenter.nordicsemi.com/.../nan_040.pdf shows the recommended sizes of the pads (0.275mm) and apertures for the stencil (0.3mm). To connect the inner rows of...
I have some nrf52382 nodes. I want to form two subnet in mesh.
if i using different provisioner to make subnet or something else ?
1. How to Create two subnets: Subnet...
Hi, I'm using metamotionR of Mbientlab that have nRF 52832 ( I attached the circuit of metamotionR )
but, I want to develop new firmware on this device. so, I started with...
Hello,
I have to implement ESB on nRF52 bare metal (using the RADIO peripheral). I can receive packets from the nRF24, but I need to implement the ACK, and I'm not sure...
Dear Nordic, dear Community,
I want to use the NRF9160 for a new IoT product row of our company.
The NRF9160 DK seems the perfect solution for evaluation and development...
Hi,
I have pca10059 and I need to remove FDS data during programming the device (for sure I do not want to remove bootloader). and it seems that nrfConnect could not do...
Hi,
I have some doubts on how the "nrf_pwr_mgmt_run" function works. As far as I know this function enters in SystemOn Idle mode, so the CPU is in sleep.
I tested this...
To the kind attention of Nordic support team,
I've got PCA10056 and PCA10040 default development kits. They are talking each other using using secured gzll, PCA10056 is...
Hi, I have RAK5010 Module which is based on nRF52840, and I also have the nRF52832 DK from nordic, and I want to program the RAK5010 using nRF52832 DK. Is it possible ? can...
Hello,
I am new in the Nordic world and try to start the Bluetooth related applications by Nordic SDK. I have the nRF5340-PDK Evaluation Board. I flashed the board as...
Hi, all
I have some questions:
1. Is the DFU advertising name could be stored in the dfu_settings_page?
2. How colud I change the DFU advertising name in the application...