Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi, I am trying the to create a mesh application using iOS nRFMESH SDK. I am able to provision the device but i am not able to get data from the getCompositionData method...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
Device: nRF52832, SD132v7.0.1, NRFSDK 16.0.0
Host: nRF52840 USB BLE dongle, pc-ble-driver-py 0.14.1, Python script, Linux
We're developing a device that's a BLE Peripheral...
Hi, I am looking for any suggestions on heart rate sensors i can use that would easily integrate with the nrf52832. I am looking to get a finalized output from the heart rate...
Hi I have a few questions about bluetooth 5.1 and the CTE packets that it transmits.
1. I know that there is a physical difference in the hardware of a Bluetooth 5.0 chip...
Hi,
I have nRF52840 dongle PCA10059. I want to use dongle as sniffer.
So how and what hex file and other thing i need to do ? To use dongle work as sniffer.
Hi,
I have been trying to get UART working properly on my custom board but also on nRF9160 DK. I'm using only UART_0.
With CONFIG_USE_AT_HOST and without any uart code...
tag v1.1.0 (have done west update) using SES 4.30c as suggested by nrf connect Compiled and flashed using SES modem firmware mfw_nrf9160_1.1.1 downloaded and updated the certificate...
I have developed a ble5 long range and meshing product but my life is way to short. using 2-3.6v batteries in parallel and only getting 2 months life in my battery calculations...
Hello everyone !!
While in test, I use Phone Mi Max 2 communicate with NRF52, sometime NRF52 send to Phone but Phone didn't received. I used sniffer and see packets to be...
