Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi. I'm trying to use command line tool, but an error occurred as shown in the picture below. Let me know why.
J-link was connected normally in segger embedded studio.
Hi All,
I need to implement security in Bluetooth. I have seen many threads but I could not get proper information regarding how can I implement or add security in a project...
Hi,
I am using the nRF52840 chip and supply iam giving from coin cell(3V). So i want to measure the coin cell voltage level monitor with nrf52840 ADC pin.
kindly provide...
Hi,
I was trying to program my sample to nRF5340's flash using nRF connect v3.4.1 and got this problem:
21:06:02.948
Application data folder: C:\Users\tuan.duong\AppData...
Hi everyone,
I was wondering if you have any advices or recommendations regarding the best type of debugging devices, or ways of debugging, for the nrf52840 Dongle, from...
I want to optimize my receiver power by putting the controller in sleep mode, that is ;-
NRF_POWER->SYSTEMOFF = 1;
And want to wake up the controller only when it receives...
When I try to increase the CENTRAL_LINK_COUNT from 8 to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max...
Hi,
I wrote a code using gps_controller.c on my thingy:91. However, i could never get a GPS FIX so i decide to try the GPS sample but it doesn't work neither.
I tried...
I'm using nRF52 DK to develop a BLE/UART application. My code is based off of the ble_app_uart peripheral example. In both my code and the default code, I get -0.1uA on the...
I am used NRF52810 controller, I wanted to know about there is possibility to work iic slave and iic master ( vice versa ) in single program ,can have any possibility about...
Hello, I have some questions regarding what MCUs to choose. I have a project which requires some controlling of external LEDs, Bluetooth communication as well as some extra...
I have used nrf52 module and it was working correctly. while debugging my PC was restarted for other pc issue. after the reboot i opened my project file my main.c file exist...
Hi! I am going to work on a project that uses a specific sensor which produces voltage outputs between 250 mV and -250 mV. Can someone help me with ideas to detect the negative...
Hi,
Once in a while, the Serial DFU stuck in flash erase. Did I do something wrong?
Background: Currently I am unable to put breakpoint in the Bootloader component that...
