Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I've been trying to store an array (SDK16,S332)
uint8_t my_data[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,.........0x23}
using fstorage I wrote an update function :
I hardcoded...
To the kind attention of Nordic support team,
I'm trying to do things like in https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059...
Hi,
I have a project which was originally written using SDK12, and have updated it to SDK16, I am sorry I know this question seems to have been asked in many different ways...
Dear,
Like I said in the title, I did use the NFC of my PCA10056 with my phone, it works, I also can read some information from nRF52840 by NFC. Right now, I programmed...
Hi Devzone:
I am working on nRF52840 with latest SDK.
I have 1 differential pair and 1 single ended pin I want to sample, single ended samples at every 40ms while differential...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
I am studying to use the nRF2460 or wireless digital audio streaming where one Tx broadcasts and several receivers listen and follow. I have the following questions: Can an...
Hi,
How can I read out a vendor model in the NRFMesh app? When I change the model ID to e.g 0x9000, I cannot see the model under elements anymore. Needs there to be any...
I have a list of characters and trying to put them in a string.
char line[13]; /* Line buffer */
NRF_LOG_INFO("Playlist : %c", line[0]); this works displaying 1 character...
We are currently evaluating the two development kits of nrf91 - On the nordic Thingy with Fractus antenna we get the nrf91 into the mobile network after about 20 seconds ...
I know this may be a duplicate of this: https://devzone.nordicsemi.com/f/nordic-q-a/37732/nrf52840-spi-clock-line-contention-causing-spi-driver-to-hang/145521#145521
I say...
