I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello ,
Is there a DFU master code through which one nrf52832 can be updated from another nrf52832. If not please let me know of some useful material to refer to implement...
Hi,
I am using the last up to date demo software for long range BLE throughput test and get systematically, as soon as I press buton 3 or 4 an error "Lost logs - increase...
What are the failure points of a properly developed DFU for OTA updates? On a consumer device where a user may do anything and everything to a device that is executing a DFU...
Hello I have a question, after watching the video: youtu.be/7h4wxyFktkQ It is mentioned that it is not recommended to connect to Google Cloud Platform from a device that is...
Hi, I am running NRF5_SDK_13.0.0_04 and s132_nrf52_4.0.3 on a custom board.
I am getting a Soft Device Fault on an NRF52832 device that I am not able to root cause. This...
Hi,
I downloaded nRF5_SDK_15.3.0_59ac345.
The first time,
Uploaded "..\examples\connectivity\ble_connectivity\hex ble_connectivity_s140_usb_hci_pca10059.hex" by nRF...
So I'm sending multiple payloads of the same width from the transmitter to a receiver and I see it sends only sends 3 times after which `TX_FULL` bit is set in the status...
Hi,
I'm working on a project involving pressure sensors.
These are to be read out via UART and then transmit the data via Mesh to a relay node up to a PC, which visualises...
Dear Sir or Madam, I am asking advice on the following matter: When trying to port the "pin_change_int" example to a nrf52833 DK the code compiles but is not showing the expected...
Hello, I developed a project starting from MQTT-SN example available in SDK for Thread and Zigbee.
I noticed that publishing and subscribing requires calls to functions...
hi，
I work in the nrf5_SDK_for_Mesh_v4.1.0_src. I want to adjust TX power based on light switch server . After setting TX power, I find that RSSI varies from high to low...
Hi.
I'm using nrf52840 SDK 16 with S140.
in my last piece of code static arrays were not enough and i needed malloc.
I used malloc without any issue, also i use cJSON...
Hi I am new to BLE energy and I would like to know if there are any SDK examples I could refer to learn about two DKs to communicate the external sensor data to the central...
Hello Nordic team,
I'm working on an nrf52840 with the SDK 15.3.0.
I'm using the SPIM instance 3 at 32MHz to interract with a Slave SPI which can support up to 40MHz....
Hi my USB keyboard application works on Windows and Linux but not on a MacBook Air with macOS Sierra 10.12.6. So I did step back and tried the combined HID example nRF5_SDK_16...
