Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
Hi, I have no found clear steps to create DFU zip packet for old one softdevice S132 SoftDevice v2.0.0.
I try to build with nrfutil pkg generate but seems its working only...
Hi,
We are currently trying the Long Range (Coded PHY) on our advertised message, but we can't see any improvement (range of about 50meters). The range can even be smaller...
Hello,
I'm using a NRF52832 with SoftDevice s132 v7.0. I also have freertos. I have an app which advertises and scans. The app is set up to trigger a break point on assertions...
I have some customers seeing an issue with advertising/connection after successful DFU. Everything was working before DFU. The changes in the new firmware have nothing to...
I am trying to port the examples/ble_central/ble_app_hrs_c project from the 52840/pca10056/s140 to a 52833/pca10100/s140 project.
Having trouble in the port from the nrf52840...
Hello, I'm using softdevice 6.0, SDK 15.0, secure bootloader buttonless S132. On the phone with Android I'm using: nRF Toolbox 2.9.0 with DFU Library version 1.10.3.
I start...
I have built a custom chip with nrf52840 on it.
I use Ses as development tool.
I took as startingpoint for software SDK15.3 with Softdevice 140
I took the ble_template...
I use SES for debugging,
the chip is nrf52840 with softdevice 140, sdk 15.3
I ported a project from 2017 and now I'm ready to compile all without any error,
but as...
I try to build and debugg a programm from 2017: SDK15.3 Sofdevice 140 5.0.0.2 alpha plattform was eclipse neon
I switched the plattform to SES because neon sucks too install...
