Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi everyone,
I'm using the nRF Connect SDK 3.0.2 and the nRF Connect Toolchain 3.0.1 with the matter ‘light_bulb’ example. I just want to do the following: 1) Get exactly...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hello, question about mcuboot, particularly the imgtool.py.
When I run west build, the build eventually fails on:
Error: Image size (0xbac8) + trailer (0xc30) exceeds...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
I'm having some trouble connecting to the onboard jlink with the NRF9151 devkit that I've recently received. The quickstart seems to detect the NRF9151 dev kit, but when I...
Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
