Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
My problem has similarities with Case 250648 (for nRF52840):
When trying to run your AT-client sample for the nRF9160 on your DK board, I cannot debug. Segger Embedded...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Development Kit v2.0.1. As Software basis I use the “Zigbee...
Hello together, I am trying to update the nRF9160 device because I can't get a network connection. I followed the guidance of a manual of this site ( https://devzone.nordicsemi...
Hi,
just for your information:
the function nrfx_twim_xfer() prints always a warning, even if there was no transmission error. I guess NRFX_LOG_WARNING() should be logging...
I am trying to modify the https_client example from ncs\nrf\samples\nrf9160\https_client on Thingy91 so that it will retrieve an authentifcation token from AWS Cognito. So...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
The nRF52832 acts as SPI Slave and we want to wake up from Deepsleep when...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
