Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello,
I am working on an IoT project using the Thingy 91 to send sensor data via Bluetooth to a remote device. Currently, I am trying to set up a simple beacon as shown...
Peripheral: SDK13.1 nRF52832
I don't want to change ConnectionParamaeter of Periperal by ConnectionUpdate request from Central. Can Periperal ignore ConnectionUpdate from...
Hej folks,
after quite some research on how to get Nordic UART and Linux together, here's as far as I got: Discover the device with hcitool lescan And - in theory - connect...
Hi all
Looking at the compatibility matrix, we understand that the following SoftDevices and SDK versions are compatible:
SDK 15.0 <---> SoftDevice S140 6.0.0
SDK 15...
Hello,
I am developing an app that uses Xamarin.Forms to communicate with BLE devices equipped with Nordic chips.
It works fine on IOS, but Android doesn't.
Android...
I have a custom board using the nRF52832 QFAA with SDK 15.3.0 and SoftDevice132 6.1.1. I'm also using an external 32kHz crystal for the softdevice clock. There are two hardware...
Hello,
I'm having issues connecting over TLS more than a single time. Using the nrf/samples/nrf9160/https_client works fine.
However, if you modify it to connect more...
Hello, I am trying to use the timer peripheral via registers only, however I am running into issues when I setup two timers and they activate at the same time. Here are my...
Hi There,
I am developing an IoT portable sensor which needs to operate across Europe Zone 1.
Talking with different MVNO it seems that NB-IoT and M1 coverage across...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I need clarification if softdevice uses RTC and if so is the Errata 20 applicable...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0)
I am looking into Erratas and working on the possible workarounds. However...
HI,ALL！
I use official routine development NRF52832，
NordicSDK\nRF52\nRF5_SDK_16\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput\pca10040\s132...
Hey!
I'm using mesh sdk 4.0, nrf5-sdk 16.0 and run the serial example.
currently I successfully provision 2 light server with the ipython interface, and to configure them...
I am trying to do service discovery using the discovery manager library on any BLE device I connect to my central. I start the service with bt_gatt_dm_start(conn, NULL, &discovery_cb...
Is there any app available that can use to track lost/retransmitted packets and get some log?
I’m trying to find best position for a nRF52840 module with chip antenna without...
