Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
Dear nordic:
I am working on a tool which can collect data from multiple ant+ sensors with different device types,like a bike computer.
It allows user to assign up to...
I want to communicate with two nRF52 devices without pairing?
It is possible? Yes means kindly give the realtive examples.
Maximum data length...
Thanks.
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
Hello,
I´m trying to connect the nRF9160-DK to the nRF cloud, using the asset tracker application. I was able to build and flash the application. But the DK can not connect...
Hello,
We are working through an issue which we found recently on the nrf sdk. The following is what is occuring:
We have two GPIO interrupts configured for low accuracy...
Hi... folks .. i am using nRF52840 development kit , i need to control the two servo motor using ble commands . I need to control the angle and speed of two motors , suggest...
