Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I am using pc-nrfutil to perform FW upgrade (transport is serial), The target is custom board with 52840 processor, running Bootloader adapted from the SDK.
For most of...
I've configured the SPI with DMA module as in the code below.
I've loaded the tx buffer with sample data and start the transaction; however, I'm not reading anything either...
Hello,
I have been working on porting the BLE UART PHY S erialization to the STM32L476 (with a Nordic NRF52832 Dev Board and STM32L476 Nucleo-64). I have read the porting...
Dear Nordic,
Running BLE mesh sensor network with multiple servers and a single client linked to a gateway.
SDK: 16.0.0_98a08e2
SDK Mesh: v4.0.0
nRF52840
The client...
I'm attempting to using pa_lna_setup(), specifically the softdevice function sd_ble_opt_set to enable/disable the radio and an external amplifier. My application is a custom...
Hi All,
Im trying to flash the pre boot-loader from here github.com/.../releases
to my nordic usb dongle.
hex-> mdk_nrf52840_dongle_bootloader-0.3.2_s140_6.1.1.hex Im...
Hi Team,
We are using the uECC library for ECC Functionalities, while connecting the debugger we are getting the pop up message like "not finding the source file".But while...
Hello guys,
I have nRF9160DK board here with me and the nRF Connect SDK v1.3.0 environment installed. I want to connect to AWS IoT Thing through the MQTT connection.
I...
When I was testing USB on SDK16.0 with nrf52840, the gateway acted as the host, the following scenario 1 worked abnormally, and scenario 2 worked normally.
Scenario 1: When...
I am using NRF5 on an NRF52840 board, building under GCC. My application needs FreeRTOS and I also need to be able to use stdlib functions such as printf() from any RTOS task...
Hi
I am reading the Irms and Vrms data from the register 0x20 so i am using nrf_drv_twi_rx(&m_twi, ACS71020_ADDRESS, m_sample, sizeof(m_sample)); where we specify only device...
Dear DevZone,
I developed an application based on ESB wireless communication protocol for the nRF52840, and I would like to perform an OTA DFU with it.
I read in this...
This has been noted a couple of times but your treatment of bit fields is just wrong in the bootloader. It not only disagrees with the documentation but it's so flawed that...
Description:
nrfutil and especially the pc-ble-driver-py seem to not work with virtual pyenv environments.
I am expecting it has something to do with the lib files _nrf_ble_driver_sd_api_vX...
<environment> - Windows10 - modem fw v1.2.0 - nrf v1.3.0
I try to receive "OK" message after sending an AT command "AT+CFUN=1" using at_cmd.c functions but can't receive...
