I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
NRF5 SDK 15.3.0 has an issue in a module nrfx_wdt.c . In function nrfx_wdt_init line of code: nrf_wdt_reload_value_set((p_config->reload_value * 32768) / 1000); causes to...
I managed, through the Nordic library for Android `thingylib` ([github]( github.com/.../thingylib)) , to connect to thingy52 and receive in the callback listener `ThingyListener...
I am following the example guide:
https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect-sdk-tutorial
however when I try...
Is there a guarantee that I can do something like: at+cfun=1;+cfun=44
and the nRF9160 will *not* start connecting to a tower? I would like to be able to interface with the...
Hi,
I have searched Devzone for changing the transmission power; even though there were similar issues related to mine but at the end, It did not help me.
I am evaluating...
Hello
I am reading sensor and broadcasting via nrf51DK its working perfectly when voltage supply is morethen 3v
but when I give voltage between 2.1v to 3v its stop broadcasting...
I cannot install the app "Programmer" automatically. The connection always fails due to poor network in our country. The error report is as follows:
Is there anyway to...
Hi Community,
printf() (and variants) fail on rounding floats: This is is probably an error in the printf implementation. I tested it with SDK 16.0 on NRF52840.
Format...
Hi,
In addition to listening the advertiser's and beacon data we also need to offer the master application - which is connected to BLE-module via UART - the possibility...
Questions about ‘Application data’ placement in the flash memory
Is there a function or other mean that could give me what is the lowest flash memory address that is occupied...
Hello All,
I am working on the Nrf52810 with sdk 15.3.
When we connect device through nrf connect app (android) i wanted to disconnect after 1 min .
I have given timer...
nRF52840 DK:
ble_app_blinky is working. After that, I flash ble_app_bms, ( working),
then flash ble_app_blinky- the smart phone is not able to discover service .
Any...
When scanning 1MBPS & Coded PHY at the same time, the probability of Coded PHY broadcast scanning is very low, and 1MBPS PHY broadcast can be scanned normally Slave configuration...
i have come across a couple posts related to providing more compatible Altium design files so that other CAD packages can import them. The best articulation of this point...
