Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi, I am using nrf52840 DK to create the uart ble app. The starting point is ble_app_uart example from SDK52 15.3. I changed pin configuration for uart so I can have RX and...
Hello,
I am looking into adding a whitelist to my central device to stop scanning devices I am disinterested in, however, I have a few questions and concerns about them...
Hi,
I saw the errata for bad onboard GPS antenna performance in nrf9160 DK v0.8.2 and 0.7.0
Was the problem fixed in 0.8.3, or is 0.8.3 still affected?
Thanks.
Hi,
I am using the nrf5 SDK for Mesh v4.0,
Windows 10,
4 DevKits PCA10056.
I have 2 DevKits as LPN (from the experimental_lpn example) and 2 DevKits as FNs (friend...
Hi,
I have a issue with the output regulation of REGOUT0.
I have a custom board based on the NFR52840-CKAA (revision D). I designed it in high voltage mode because I have...
Hi, I'm getting a crash when discarding an advertising packet.
Roughly what I do is:
Which crashes at advertiser_packet_discard().
GDB trace:
It looks like packet_buffer_pop...
When and by what logic Peer Manager performs garbage collection on FDS?
I have a single number stored also in FDS and I’m wondering if gc performed by Peer Manager will...
Hello,
I'm still just starting to deal with Zigbee and I have a question. I use 2 nRF52840 chips. One as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
Hello,
I never used BT modules before. I'm going to buy some bluetooth modules to add wireless to an existing board.
I need module with following characteristics:...
Hi，I want to write the firmware to 52832 from android system by UART .I have readed the firmware into bytes, and then do not know how to compose the bytes to write into serial...
I have the following situation:
My device receives a number of RF packets, changes to TX mode, sends some data, goes back to RX mode and it should be able to access the...
