Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello,
I am trying to fix the UART communication error(APP_ERROR_HANDLER(p_event->data.error_communication);).
I am sending a command(0x87,0x14,0x11,0x33,0x44) continuously...
Hi,
Sorry if this question is too simple - I tried to search existing threads before posting.
I just received the official nRF52-DK and would like to get it started, I...
Hi
i have LIS2DH working ok just having problem with the order of return values, maybe just a quick fix.
LIS2DH is running on 10Hz, low power mode, I receive interrupt...
Hi!
We are experimenting with BLE Mesh on nRF52832.
Our setup includes around 50 sensors located in a building which need to report sensor data ( 12 bytes ) in real time...
Hi,
I'm trying to configure nRF51 usb dongle as server but can't get it to advertise.
Neither 'Advertising setup..' nor 'Start advertising' option seem to do anything...
So I've been banging my head against the wall for a little bit now and this just isn't making sense to me.
I downloaded the NRF Toolbox app on my phone, and I compiled the...
I am working on SDKv14 with S132 softdevice and was trying to modify the Heart Rate Example to vary the Manufacturer Specific Data after each advertisement. After searching...
Hi,
I have recently started working on nrf52832 chip, don't have much knowledge on that. I have two chips (nrf52832) one is running on bluetooth version 5 and other one...
I'm evaluating BT5 feature using the PCA10056 preview dev kit and SDK v15.
When working with LE Coded PHYs, is the S2 or S8 version? In the SoftDevice release notes only...
Hello,
I'm testing the bootloader with SDK v.15 and I found a state when DFU won't resume (on BLE transport).
I crashed nRF Connect randomly, in that case, between the...
Hi All,
I am designing circuit to Turn ON 4 LEDs at a time based on high and low of GPIO
Supply voltage is 3.3V my doubt below circuit is fine whether it will work fine...
I try onnrf52804 (nrf52840-DK) with SoftDevice V6.0.0
----------------------------------------------------------------------------------
ble_gap_scan_params_t s_scan_params...
Hi all,
I want to use the python scripts provided in application notes in nordic documentation to run DTM example flashed into nRF52840 SoC. So when I open command prompt...
In the infocenter, after searching for something, if you click on an item in "Search Results" (left hand panel), it brings up the associated page in the right hand panel....
