Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am making a GPS tracking system using NRF51822-QFAC. I am using 2 UARTs, one of the (external) GPRS IC and one for (external) RS485 communication.
The UART peripheral...
HI,
I tried to compile Thingy v2.1.0 with keil. And sereval file are missing.
Actually i work with your SDK 14.0.0, i find so many missing file, but not all.
Can...
Hi,
I am currently testing with a USB MSC example .
FATFS_QSPI is disabled because the file system is not used,
Subclass has also been modified to 0x06 -> 0xFF.
...
Hi,
I am implementing experimental_bootloader_secure_usb code example on PDK PCA10056 V0.9.2 using Sdk v14.0 and also tested with Sdk v14.2 but in both cases Windows 10...
With SD140 v6.0.0.6 having been released, will an accompanying example project that demonstrates simultaneous use of BLE and USB be released? Will this be included in the...
Dear devzone,
I am currently merging the Mesh SDK into the normal SDK to run BLE & BL mesh concurrently.
Followed multiple guides to get it working, at this moment I am...
I use nrf52832 development kit,nRF5 SDK for homekit.
Now I have read and write to UUID, want to realize how to handle the notification operation, and call what API?What are...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
Hi. I am connecting to and establishing a bond between my Android phone and the nRF52832 board using the s132 SoftDevice. I'm in a situation where the Android phone has a...
Hello,
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described here
Another nRF52840 Development Kit...
Hi there,
I'm trying to run the beacon s130 pca20006 example on a custom board. There are 2 main differences between the pca20006 and my board:
There is a 32 Mhz...
Hi,
it seems there was lately a new IC revision release of the nRF52840.
Is the nRF52840 IC Revision Engineering B 100% pin compatible to Engineering A, i.e. pinning...
Please excuse my basic question but I'm new to this - I am needing to have data collected from probe/sensor, which would be in a device, sent every hour to an android app...
Hello,
We plan to switch between two sets of UART pins for factory testing. One set will talk to an IC in our design and the other to a USB port through FTDI. Since simultaneous...
