Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello dear
I have a question about NFC on RF52832. On section 42 of datasheet, says:
"The NFCT peripheral (referred to as the 'NFC peripheral' from now on) supports communication...
hello support team,
i have seen thread and sdk14.2.0/examples/peripheral/SAADC example
pca board: PCA10040
can anyone suggest how to read battery status using handler...
Hi,
I am trying to set an nrf52840 pdk (with SDK14 and s140_nrf52840_5.0.0-2.alpha) as peripheral and central at the same time and another nrf52840 pdk just as a peripheral...
Hi,
I play with pca10040 and the light-switch example from SDK for Mesh v1.0.1. Everything works but I wonder why the advertising signals are not seen by nRF-Connect Scan...
Dear Developer Zone,
I am using nRF51822 with softdevice.
Small question about device reset : To reset the chip, do I need to do NVIC_SystemReset() or sd_nvic_SystemReset...
Hello,I'm porting a freeRTOS project to nrf51822 QFAA with 256k flash and 16k ram. I want to use s130 2.0 sd.
Previously this project was done with s110 sd and everything...
Hello All,
Please find the attached schematic , please review the same and give your valuable feed back , we are using NFC functionality in the same . earliest reply will...
Hi, We have an application with 1 central and multiple (6-7) peripherals. The peripheral is running a custom service and the central is running a custom (central) service...
I try to run UART/Serial Port Emulation over BLE on SDK v14.2.0 with nRF52 DK and nRF Connect on Android phone following link " http://infocenter.nordicsemi.com/index.jsp...
I am trying to run the coap ipv6 based example code provided in nRF51 IOT SDK. I am using my Linux PC along with a BLE adapter as a BLE enabled router. I can successfully...
I came across this a while ago, however it gives no indication as what releases, of Segger J-Link suite, each nordic J-Link OB download has been tested with.
Is there page...
Hello, I am looking for documentation on the Mesh DFU Protocol. It looks like it is the same DFU that the mesh branch of the nrfutil python app is using. I would like to do...
