Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi, I want to use the ADC peripheral (SKD16) and I am looking for the most energy-efficient way of doing this. I design a prototype that will be based on nRF52840 IC and will...
For a temperature sensing application, I am trying to implement a TWI interface with a TMP116 temperature sensor. I am using Keil uVision 5 to write the program. I have been...
I am attempting to port a BLE application to the nRF52840. The original application used a standard HCI serial interface so I am trying to adapt that to use the Nordic SoftDevice...
Calling the lte_lc_connect() function eventually leads to the code breaking on:
fault_s.S line 104
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE) /* force unlock interrupts...
Hi I am using NRF52 board to interface analog sensor and this board further transmit the data ro sink node. I am using saadc example but unable to get callback or my interrupt...
We have a set of custom boards I am working on debugging. I was able to get our software onto the device via nrf jprog tool by uploading a merged hex file (with SD + bootloader...
Hello,
I would like to turn off the logging to UART0 completely on my custom device.
In the past, I have been able to do this using various config options and reduce the...
Hi!
I am currently playing around with the example combining uart and MQTT from this thread , and it seems to work okay. But when i try to send more than 10 characters over...
My end goal for development is something like the following.
Master sends 0x00 slave sends back 13 bytes of data. Master sends 0x01 slave sends back one byte of data....
Hi,
I need to use the cryptocell in a project with a preemptive OS. Are there any relevant code examples available, or at least some general guidelines and precautions ...
Hello,
I would like to implement the network time synchronization from the Openthread API to the existing simple_coap_client example from the Thread and Zigbee SDK. I'm...
Can we increase the packet size in Nrf52 Beacon example ? I want to send UUID=16 Bytes + Major=4 Bytes, Minor= 4 Bytes + RSSI= 1 Byte i.e Total = 25 Bytes. I am using SDK13...
Hi,
Due to several reasons, we can't use the crypto API:s provided by the NRF_SDK (version 15.00) so we are creating a "driver" for direct access of the CC310 via the CRYS_...
Dear Sir/Madam
Currently we are working with nRF9160-DK it is having nRF52840 Board Controller. in this We want to use NRF52840 as a BLE functionality.
We want to develop...
