Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
HI
my Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to load device name from fds when initial,
my goal is sending message to my board to change...
For some reason, it seems that I am not able to send any raw data with the BLE radio. I am able to configure the radio and start it successfully. However, the radio never...
Hi,I used Nrf52832 connect BMX055 with i2c, I use sdk nRF52_SDK_11.0.0 example examples\ble_peripheral\ble_app_cscs and add my code to read the BMX055,but when it work a short...
Hi Nordic,
i have a question regarding the emBuild.exe tool and the optimization level it will use during building a hex file. I'am using the following command combination...
Hello,
How can I determine the current consumption of Bluetooth 5 use nrf52832 soc with transmission at -4 dm when in the datasheet mentioned only the current consumption...
Hi,
I've just got an Arduino Nano 33 BLE with the NRF52480 chip on it.
I've been trying to manage the Pin configuration by setting the register values through the Arduino...
Hi,
I am using a NRF58240-dk pca10056 S140.
I have an external SD card device connected which, I am writing live sensor data to then advertising that data over a ble advertisement...
Hi ,
The device required to keep advertising during the connection established.
It is human interface device which mean it is peripheral device as well.
I would like...
Hello there,
A while ago I started developing on the nRF9160DK but I found an issue that I do not know how to solve by myself.
I used two SIM cards: the one from iBasis...
._build\nrf52832_xxaa_s132.axf: error: L6002U: Could not open file ..........\external\micro-ecc\nrf52_keil\armgcc\micro_ecc_lib_nrf52.lib: No such file or directory
Hi all,
Is there any sample sdk example for transferring audio file from nRF52840 to my mobile? Is it possible to transfer audio file through Nordic Uart Service? Thanks...
Hi,
I am developing a product based on nrf52840 soc, I need to write a softdevice, program hex file, bootloader on the chip. when I want to select them all in the nrf...
I am trying to set up the LPS22HB sensor with an nRF52840. I am starting with the twi_sensor example(SDK16->examples->peripherals->twi_sensor) and adding the lps22hb example...
We have added custom HID firmware and are able to discover it on the Android Bluetooth Settings app. iOS fails to show the Bluetooth device on iOS Bluetooth Settings app....
Hi,
My task is..
Device will advertise for 20 seconds if there is no connection then it will go to sleep mode for 40 seconds. After 40 seconds it will wake up from sleep...