Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
Hi all,
Actually I'm building with vscode my firmware for a custom board build with an nRF9151 non secure. After building I got a merged.hex file, this is the file upload...
Hi All,
we are deciding which chip to buy in order to make our AoA trasmitter (CTE packets).
According to https://www.nordicsemi.com/Products/Wireless/Bluetooth-Direction...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Hello forum ,
Here i tried to write and read from flash qspi w25q64 but read and write both are failed ..i m using nrf52840 kindly pls help me for read and write
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
I am developing a firmware for nRF52810.
Does Zephyr support debounce care for push button switches in ncs v2.6.1?
It seems that CAF supports it, but I don't plan to...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hello
I have a very strange problem
A custom nRF52840 board has a charge detect pin, P1.6
A gpio callback is installed to wake it up on charger connect/disconnect
...
