Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
I need my sara sara-r410m-02b ublox module to connect to the cellular network using at commands. For this reason I require to send the commands by means of programming lines...
Hi
I have a custom who is using 52832 to develop a Bluetooth door lock, including a NB-iot module, The door lock is unlocked via app Bluetooth.
the question is : There...
Hey all,
Have just been messing around with the board, everything was working fine until I tried to follow this guide to install CircuitPython onto the nRF. I got it into...
Hi there!
I am currently trying to follow the SDK instructions to get everything up and running. I followed all steps closely and didn't run into any errors apart from the...
Hi there,
Because of the current corona virus I could order a debug in/out cable for the Segger's build-in debugger (P18 & P19). But I have the cable it self and slot compatible...
We'd like to be able to store a few items including mutable keys, and unique identifier in each device that is generated on initial boot of the product. I'm just starting...
Is it possible to pair the nrf52 DK and nrf52 dongle through bluetooth? My project requires that the nrf DK sends data (sensor values) to the nrf dongle, and from the dongle...
Hello, this concerns SoftDevice spec 7.1 and nRF5 SDK v16.0.0.
I noticed that ESB has interrupt handlers occupying priority levels 0 and 1 according to the SDK documentation...
Hi,
Is it possible to disable logger at runtime on nRF9160? I would like to have a logger at device's first startup after flashing (like in production test mode) and then...
Hi Team,
We have a new requirement on students tracking system when the students are in School bus.
School bus can contain seats of 25-50 depending on the type of bus...
