I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello. I'm using the example of the light_switch_server project. I need to configure a server (light bulb) driven by 3 clients (buttons), how can I do? I tried this way, but...
Hello Nordic,
I have to transmit data from the nRF Chip(now i'm testing nRF52832 DK Board) to a PC on UART serial.
Each beacon has transmitted advertising and scanRSP...
Based on the nRF24L01P Product Specification 1.0, after 24L01+ enters into Standby-II state, the only 2 ways to leave this state are 1, set PWR_UP to 0, 2; 2, Feed data into...
I've picked up the DK after a break. Installed the toolchain on my new laptop and was ready to throw the 'blinky' example from the SDK on to it to get started. It did not...
Hi Nordic experts:
I use a device with thingy52-provision-demo firmware(from git-playground), and another device with serial-example to provision the thingy-provision-demo...
Hi.
I want to advertise switching 1Mbit PHY and CodedPHY every 5 seconds.
I designed it like this based on nrf52 ble app uart long range example.
advertising_start(coded...
Is it possible for an app after having gone to sd_power_system_off to reset by button without triggering DFU?
The app seems to need CONFIG_GPIO_AS_PINRESET to be set so...
I am working with production Rev 1 on nrf52840 DK v1.0.0 (2018.19). The spec section 6.35.10.2 Bulk and interrupt OUT transaction say
Until that transfer is finished,...
I am working on mesh application icatin nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for...
Hi all,
I am testing DFU example in Mesh SDK . I follow this tutorial : http://infocenter.nordicsemi.com/index.jsp . But when I execute to step 4 :
I get this error...
Hello,
I am new to Nordic products so please apologize me if I am asking a trivial question, but a bit lost on it. I would like to use Thingy 52 board for my project ( I...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
