Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I use the nRF5 SDK 11.0.0 and with it we can easily build the examples with armcc from Keil, or with gcc (arm-none-eabi-gcc) from the command line using your Makefiles...
The current configuration looks as follows:
IDE: Eclipse
Toolchain: ARMGCC
SDK: SDK5_NRF_14
DK: NRF52DK-PCA10040
I am trying to port the 'bootloader_secure_ble'...
Hi,
I've combined the secure serial and ble bootloader and using it for my custom board. I tried flashing my application hex over serial using nrfutil. I get a device programmed...
Hi,
I am working on the nrf51822 board and i am only the PAC20006 board version seems to be working on it. I am using sdk 11 and soft device version s130_nrf51_2.0.1 s suggested...
Planning for Evaluation of nRF52810.
I am thinking of using nRF52 DK for this and i want to know if there is any beacon with nRF52810 which i can use for this evaluation...
Hi All,
1.One master BLE has to connect to Slave BLE, then both device should read other RSSI and sent the data through UART.sending the RSSI should be every 200 millisec...
Hello,
I try to use those functions for printing log massages on the Segger RTT terminal, but I have many problems with that.
1. How can I use this function without printing...
Hi everyone,
I am using nRF52832 kit (PC10040), eclipse and softdevice S132 V5.0.0 for developing a BLE service. I follow the service tutorial and I refer to the code from...
i want to connect raspberry pi 2 with nordic thingy 52 via ble.....while issuing connect command after gatttool -I -b Mac addr it is throwing some connection refused error...
i want to know about how nrf51822 module's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
All,
I'm relatively new with the Nordic Ecosystem and have been playing with the example projects on the nRF52 DK and have successfully gotten several examples up and running...
Using Keil v5, ARMCC 5
Pin state equals:
Level 0 - 0x00000000 - pin low
Level3 breakpoint after read - 0x00000040
Level3 breakpoint before and stepped through -...
I am advertising a service and providing scan response data. It is not clear to me whether I should be bothering setting up the values of the ble_adv_modes_config_t structure...
